I use a microwave oven for a lot of crafting projects (heating, curing, and drying materials). This often needs to be very precise and controlled. I experiment with times and power levels. However, I run into situations like these kinds of unexpected results:
This isn’t flaky microwave oven performance; the results are perfectly reproducible.
What’s causing such big discrepancies from the expected results?
Just for clarification, a microwave oven is really the right tool for the applications I use it for. These are generally “interactive” requirements to add small, controlled increments of heat. The issue is that when power level settings are used for short durations, the results can be radically different from what is “logical”.
I wanted to have an official citation for this fact. This is the disinfection process for a neti pot or neti rinse. In fact, I have experienced melting the plastic from using the microwave too soon.
Consider adding rest periods during your timing experiment.
Hope this is helpful. 🌊 🌙
Answered by Not The Face on November 24, 2021
I suspect you're heating fairly small quantities. If so another way (in addition to Fixer1234's answer) to reduce the power reaching your material is to heat something else at the same time. This could be scrap material, or it could be a cup of water (with a loose lid if you want to minimise steam).
Very very roughly the energy should be absorbed in proportion to the mass (I'm making some big assumptions* here, but it's somewhere to start). So if you weigh your materials, and add a cup with the same weight of water, you should effectively get about 50% power. Overall I suggest combining this with reducing the power setting.
I've actually given up on melting chocolate in the microwave, unless it's mixed with butter, as it's more fiddly than heating it in a dish over a pan of boiling water. That may be suitable for you.
* One important assumption is that the microwave heats evenly. That's probably not true; most have hotspots, so position is important. Another is that water and your material absorb microwaves equally. If the material is designed to be microwaved it's probably a decent absorber, likely water based, so it will be close enough.
Answered by Chris H on November 24, 2021
Only a few microwave ovens control the microwave power level on essentially a continuous basis. That is, if you set the power level at 30%, the oven runs at 30% power output. Most are based on turning the microwave power on at 100% for a given portion of a fixed time increment, like 30 seconds or 1 minute. Then the microwave power shuts off for the remainder of the time increment, and the cycle repeats.
My microwave oven is based on a 30 second cycle, so the power level setting translates to 10% increments of 30 seconds. At 50% power level, there is microwave power at 100% for 15 seconds, none for the next 15 seconds, then the cycle repeats. If the time is set to less than the resulting power-on time, the oven stops when the time runs out.
So in my first example, with a 50% power level, the material gets 15 seconds of full power whether the timer is set for 15 seconds or 30 seconds. In the second example, with a 20% power level, the material gets 6 seconds of full power at the start of the first 30 seconds, then another 5 seconds of full power before it shuts off at 35 seconds (almost double the energy despite the small time increase).
To get precise amounts of microwave power using the power level setting, you need to base it on the cycle time of your oven. You can tell what the cycle is for your oven by listening to it cycle the power on and off and check the oven's clock to see the time between power-on cycles. If you need brief bursts of microwave power, you may need to use a very low power level (and the process may take a long time).
The way the power level actually works makes it not particularly useful for short-duration requirements. For those, I typically do what Chris H suggests in the comment -- do it manually at full power to get exactly the duration needed. The main benefit of the power level setting is when you need a lot of cycles of short duration, and doing it manually would be tedious. Understanding the cycle action lets you ensure that the duration at full power doesn't exceed a certain number of seconds at a time.
Answered by fixer1234 on November 24, 2021
1 Asked on December 9, 2021 by andrey-morozov
2 Asked on December 9, 2021
3 Asked on December 9, 2021
1 Asked on December 9, 2021 by cynicus-rex
6 Asked on November 22, 2021
3 Asked on November 22, 2021 by newbiewantstomaster
1 Asked on November 22, 2021 by v-grophey
2 Asked on November 22, 2021 by jack-twilley
2 Asked on November 22, 2021 by gema
2 Asked on November 17, 2021 by jeffrey-blake
6 Asked on November 17, 2021 by aspen-the-artist-and-author
3 Asked on August 25, 2021 by atl_dev
4 Asked on August 25, 2021 by jose-antonio-reyes
1 Asked on August 25, 2021 by yazmin-osoyo
Get help from others!