TransWikia.com

Calculating shaft diameter

Engineering Asked by php_nub_qq on December 14, 2020

I’m designing a circular shaft that’s going to carry a spread radial load of about 200kg and also transmit a 160Nm torque. I’m not very familiar with materials but what I’m guessing I’ll be able to get at a reasonable price locally is some lower grade steel.

Replacing the spread load with a single force in the middle of the shaft I guess will look something like this

enter image description here

Both points A and B are symmetrical so I’m taking in consideration only half of the shaft and calculating for that.

$$T = Fell = 200 cdot 0.5 = 100text{ kNm}$$

Where $T$ is the torque at point $A$ created by the force $F$.

The tensile stress on the shaft will then equal

$$t = dfrac{T}{W}$$

Where $t$ is tensile stress and $W$ is section modulus.

For a solid circular face the section modulus equals

$$W = dfrac{pi d^3}{32}$$

Now I have to assume either $t$ or $d$ in order to solve. I looked it up in this table and it looks like the tensile yield strength of steel is 350 kPa so I’m taking a conservative estimate of 300 kPa for $t$.

$$begin{align}
d^3 &= dfrac{32(T / t)}{pi}
&= dfrac{32 cdot (100e3 / 300e6}{pi}
&= 0.003397028
therefore d &= 0.150text{ m}
end{align}$$

Obviously there is something wrong either in my logic or calculations because I’m getting unrealistic results.

I went ahead and calculated the torsion stress as well with this formula. I found that shear stress for steel is about 200-300 kPa so I’m again taking a conservative 200.

$$begin{align}
d &= 1.72 cdot left(dfrac{M}{tau_{max}}right)^{1/3}
&= 1.72 cdot left(dfrac{160}{200e6}right)^{1/3}
&= 0.0159 ~ 16mm
end{align}$$

which seems about right.

I was thinking of getting a 20 mm diameter profile but I would rather play it safe and ask for some help instead of just assume it’s going to hold.

2 Answers

According to a couple of textbooks on machine design and assuming that your FBD is correct, the maximum bending moment occurs at the centre of the shaft.

For a point load, it is equal to:

$WL/4 = M$

Where W is the point load and L is the length of your beam.

$(200*10^3)*1/4 = 50*10^3 Nm = 50*10^6 Nmm = M$

According to the maximum shear stress theory the combined torsional and bending stress is given by:

$T_e = sqrt{M^2 + T^2}$

But we also know that

$ T_e = (pidiv 16)*tau*d^3$

Where tau is the allowable shear stress for each material.

Substituting the numbers into the first equation and then equate both of the $T_e$ values. You can then solve for d. This is one of the answers.

But also taking into consideration the bending moment using maximum normal stress theory,

$ M_e = 0.5(M + sqrt{M^2 +T^2}) $

When designing the shaft for the bending moment, we can apply the formula shown:

$M_e = (pi div 32)*sigma_b*d^3 $

Where $sigma_b$ = Ultimate/Allowable Stress

Substituting the numbers into the first equation $M_e$ equation and then equate both of the $M_e$ values.

You can then solve for d. This is one of the answers. Find the largest diameter out of the first and second equation and use it. You should also apply some safety factor in the allowable stresses and maybe the diameter. If the load which you stated is uniformly distributed the maximum bending moment will also change which is contrary to your point load diagram. I am also unsure about the action of fatigue.

Correct answer by Amit on December 14, 2020

@php_nub_qq, Even if its a bit late, my main comment is that you probably have messed up with the engineering units.

The tensile stress you are referring to, is probably 3 order of magnitude lower than the actual UTS even of a common grade steel (300MPa instead of 300 kPa). That allow would mess up and produce significant differences in the loads.

Also I concur with @Amit in that your method you describe is valid only for the bending moment imposed from the 200kN load. In your calculation you do not account for the shear stress due to the torque. Due to my late answer I will only point you to the following link https://www.engineeringtoolbox.com/torsion-shafts-d_947.html, so that you can calculate $tau_{xz}$

After that, you could use the maximum stress theory or Von Mises (it will be much more straightforward in your case and also differences in most cases are negligible).

$$sigma_{VM} = sqrt{sigma_{xx}^2 + 3 cdot tau_{xz}^2}$$

For justification about that, you best do a bit of reading at Norton or Shigley's books, and look at design of shafts under combined loading.

EDIT 1: I performed a rough analysis (linear) and the estimated normal stresses (due to bending) compared to the shear stresses (induced by torsion) are approximately 50 times larger in the scenario you are describing.

E.g. assuming a maximum tensile stress of 200 MPa, the required diameter is approximately 4.7[cm]. For that diameter the torsionally induced shear stress is about 8[MPa].

Bottom line, from an engineering point of view you are ok just considering the bending stresses only.

Answered by NMech on December 14, 2020

Add your own answers!

Ask a Question

Get help from others!

© 2024 TransWikia.com. All rights reserved. Sites we Love: PCI Database, UKBizDB, Menu Kuliner, Sharing RPP